Dedicated to the Mako Shark II corvette
totally free for all. no ads. no pop-ups. no fees.
Home History Owners Forums Clubs Vendors Links Contact


Subject: "Shorties door jam..." Archived thread - Read only
  Page 1 | 2 | 3 | Previous Topic | Next Topic
Printer-friendly copy     Email this topic to a friend    
Conferences Mako Shark 2 Mako/Maco Replicas Topic #214
Reading page 3 of 3 pages

 
ShawkRider

 
Click to EMail ShawkRider Click to send private message to ShawkRider Click to view user profileClick to add this user to your buddy list Click to send message via AOL IM
 
Member since Mar-24-03
2857 posts
21. "RE: Shorties door jam..."
Jul-31-05, 02:00 PM (EDT)
Good topic, just wants to keep it fresh on my mind for my personal mod's.

McBrain


 

Printer-friendly page
rockcrusher67

 
Click to EMail rockcrusher67 Click to send private message to rockcrusher67 Click to add this user to your buddy list Click to send message via AOL IM
 
Member since Sep-7-02
1479 posts
22. "RE: Shorties door jam..."
Jul-31-05, 07:54 PM (EDT)
Really wouldnt take much to achieve this, just close the door -gring and glass up the lower part of the door to 1/4 panel gap- after it has set good just recut the gap as you want it . then get inside the wheel well and seperate the 1/4 panel piece from the inner well so you can get th door open. grind and finish as desired. probably do both sides in a day and a half.

rockcrusher67


 

Printer-friendly page

 
ShawkRider

 
Click to EMail ShawkRider Click to send private message to ShawkRider Click to view user profileClick to add this user to your buddy list Click to send message via AOL IM
 
Member since Mar-24-03
2857 posts
23. "RE: Shorties door jam..."
Aug-02-05, 01:09 AM (EDT)
Thanks for the idea, i've been trying to figure out a way of doing it without adding the widebody fender flares. This could work.

Thanks again.

McBrain


 

Printer-friendly page
rockcrusher67

 
Click to EMail rockcrusher67 Click to send private message to rockcrusher67 Click to add this user to your buddy list Click to send message via AOL IM
 
Member since Sep-7-02
1479 posts
24. "RE: Shorties door jam..."
Aug-02-05, 09:38 PM (EDT)
You wouldnt have to have flares , very simple.

rockcrusher67


 

Printer-friendly page

 
2Sharksadmin

 
Click to EMail 2Sharks Click to send private message to 2Sharks Click to view user profileClick to add this user to your buddy list
 
Member since Jul-9-02
3546 posts
25. "RE: Shorties door jam..."
Aug-03-05, 07:38 AM (EDT)
I like flairs, just wide enough to cover the tires. That keeps the rock chips down a little. Just my preference, not a law.

"Randy"


 

Printer-friendly page

 
ShawkRider

 
Click to EMail ShawkRider Click to send private message to ShawkRider Click to view user profileClick to add this user to your buddy list Click to send message via AOL IM
 
Member since Mar-24-03
2857 posts
26. "RE: Shorties door jam..."
Aug-03-05, 07:48 AM (EDT)
Now that i didn't know, yet more usefull information to take into
consideration. I do appreciate all the comments and idea and Randy's
assistance in explaining the shorty.

Thanks

McBrain


 

Printer-friendly page


Page 1 | 2 | 3 | Conferences | Forums | Topics | Previous Topic | Next Topic

© 1997-2006 David N. Junod. All rights reserved.
© CORVETTE is a registered trademark of the General Motors Corporation & Chevrolet Motor Division. Chevrolet Motor Division nor any subsidiaries of GM© shall bear any responsibility for MakoShark2.com content, comments, or advertising. MakoShark2.com is independent from GM© and is not affiliated with, sponsored or supported by GM©. Copyright/trademark/sales mark infringements are not intended, or implied. All Rights Reserved